Numaco Labeling
 
Numaco Labeling
Printers and hardware

Printheads and wear parts

Four parts of a thermal label printer wear by design.

The figures on this page are the manufacturers' own.
1 2 4 3
PartWhat it doesWhat the manufacturers say
1PrintheadA row of tiny heating elements, 8 per mm at 203 dpi, that print through the ribbon or onto direct thermal labelsWarranted by distance printed, see below
2Platen rollerPulls the label past the printhead and presses it against the headTSC warrants it for 12 months or 2 million inches; Zebra's industrial printers in Europe, for 12 months
3CutterCuts labels, tags or continuous mediaZebra: clean it after every roll of pressure-sensitive labels. TSC warrants its care label cutter for 12 months or 400,000 cuts
4Tear barThe toothed edge labels are torn off againstZebra: clean it once a month

How printhead life is measured

By the length of media that has passed under the head, with a time limit beside it. The printhead warranties:

Manufacturer

Printhead warranty, whichever comes first

Zebra, in Europe and the Americas

1 year or 1 million inches (25.4 km)

Honeywell

1 year or 1 million inches

TSC

12 months or 1 million inches

cab

24 months or 50 km in thermal transfer, 24 months or 25 km in direct thermal, on label material cab has approved

These are warranty limits, not a forecast for your line. How long a head lasts depends on the four things below. A worn head is replaced, not repaired: Zebra does not repair printheads.

What shortens it

Ribbon narrower than the label. Where the label runs past the edge of the ribbon, the label rubs the head directly. Zebra recommends a ribbon at least as wide as the label, and cab one slightly wider; TSC warns that one much wider wrinkles.

Abrasive labels. Zebra names media with abrasive particles, and cab warns that rough labels can shorten printhead life. cab's printhead warranty covers only label material it has approved.

Test labels marked D = 22 and D = 18 coming out of a label printer, printed at two darkness settings

Darkness. Too high a darkness or heat setting wears the head early. Zebra and cab both advise the lowest setting that still prints well, and cab does not cover overheated printheads.

Cleaning. Zebra and cab call for cleaning the printhead at every new roll of ribbon, or every new roll of labels in direct thermal printing, with isopropyl alcohol of 99.7% (Zebra) or over 99% (cab). Other cleaning agents can damage the head, and TSC warns they may void its warranty. Static discharge and sharp tools damage it too.

A worn or dirty printhead also prints codes that fail their print quality grade: see 1.1.2 GS1 and serialisation.

203, 300 or 600 dpi

1 mm
203 dpi
1 mm
300 dpi
1 mm
600 dpi

The same ring, 2 mm across, in the dots of each resolution, all three drawn at one magnification. Each square is one dot the printhead can print.

ResolutionDots per mmDot size
203 dpi80.125 mm
300 dpi120.085 mm
600 dpi240.042 mm
  • 203 dpi is enough for most labels. A GS1-128 barcode on a pallet label needs a narrowest bar of 0.495 to 0.940 mm, which 203 dpi prints with four to seven dots.
  • 300 and 600 dpi for small text and small codes. cab recommends them for small fonts and for graphics on type plates; Zebra for very small labels, such as component labels in electronics and specimen labels in pharmaceuticals.

Finding the part for your printer

By model: every printer below links to its model page, which lists the printheads and wear parts with the numbers its maker publishes, or says how to ask for them. The model and the resolution decide the printhead.

Printers by maker

By number: type the manufacturer's part number or our article number into the part-number search.

Part-number search

Other spare parts, such as sensors and boards: 6.4 Spare parts.

Spare parts

Printers by maker

Zebra

cab

TSC

Epson

Honeywell

Toshiba

We supply printheads and wear parts for the printers we sell, the printer maker's own and compatible ones. A printer sent to our workshop near Zurich has them fitted there, see 8.1 Repair and RMA.

Last checked: 21 October 2026.

Talk to us

Preparing a validation, an inspection or a change to your labels?

The first engagement is free: a half-day review of your current label print chain, ending in a written list of gaps.