cab SQUIX 6.3
A 6 inch industrial label printer for thermal transfer and direct thermal labels, at up to 250 mm per second and up to 300 dpi.

maximum print width, at 203 dpi
maximum print speed
highest resolution
maximum label width
What fits the SQUIX 6.3
Drawn to one scale.
Labels: 46 to 176 mm wide; 0.03 to 0.6 mm thick; on rolls up to 205 mm across, on a 38.1 to 76 mm core.
Ribbons: 50 to 170 mm wide and up to 600 m long, on a 25.4 mm core, wound with the colour layer outside or inside. cab says a ribbon should be at least as wide as the liner material.
See , , or start from what the label must survive in the .
Specification
The base model. Options change some of these figures.
Printing
- Methods
- Thermal transfer and direct thermal
- Resolution
- 203 dpi and 300 dpi
- Print width
- 168 mm at 203 dpi; 162.6 mm at 300 dpi
- Print speed
- Up to 250 mm/s
- Print length
- Up to 9,000 mm at 203 dpi; 4,000 mm at 300 dpi
- Media sensors
- Transmissive sensor and reflective sensor from below or above, 5 to 60 mm from the locating edge; material passage up to 2 mm, 5 mm as an option
Labels
- Width
- 46 to 176 mm
- Height
- From 6 mm without backfeed; from 12 mm with backfeed or when peeling
- Roll
- Up to 205 mm outside diameter, on a 38.1 to 76 mm core; wound outside or inside
- Thickness
- 0.03 to 0.6 mm
- Liner
- 50 to 180 mm wide; 0.03 to 0.16 mm thick
- Continuous
- 50 to 180 mm wide; 0.03 to 0.5 mm thick; cardboard up to 300 g/m2
- Materials
- Paper, cardboard and synthetics (PET, PE, PP, PI, PVC, PU, acrylate, Tyvek) on rolls or fanfold
Ribbons
- Length
- Up to 600 m
- Width
- 50 to 170 mm
- Core
- 25.4 mm
- Roll
- Up to 80 mm outside diameter; colour layer outside or inside
Connections
- Standard
- RS232-C, USB 2.0 Hi-Speed for a PC, Ethernet 10/100 Mbit/s with IPv4 and IPv6, static IP or DHCP, IEEE 802.1X, two USB host ports on the control panel and two on the back, SD card slot (SDHC and SDXC, up to 512 GB), USB host 24 V DC for peripherals
- Optional
- Digital I/O interface with 8 inputs and 8 outputs; USB WLAN stick, 2.4 GHz 802.11b/g/n, or with a rod antenna 2.4 GHz and 5 GHz 802.11a/n/ac
- Network protocols
- RawIP (port 9100 by default), LPD/LPR, FTP/FTPS, HTTP/HTTPS, WebDAV, SOAP, SNMP v2, SMTP, PJL, OPC UA and OPC UA DI, VNC, mDNS
Printer languages
- cab JScript and abc Basic Compiler; ZPL II as an option, with the data stream to be tested in advance
Unit
- Display
- 4.3 inch colour touch display, 272 x 480 px
- Versions
- Basic with tear-off plate; P with peel-off and internal rewinder; 6.3 L linerless
- Memory
- 256 MB RAM, 50 MB flash (IFFS); 800 MHz 32-bit processor
- Size
- 312 x 288 x 460 mm, width by height by depth
- Weight
- 14 kg
- Power
- 100 to 240 V AC, 50/60 Hz, PFC; standby under 10 W, typical operation 100 W, up to 200 W
Environment
- Operating
- 5 to 40 °C; 10 to 85% humidity, non-condensing
- Storage
- 0 to 60 °C; 20 to 85% humidity, non-condensing
- Transport
- −25 to 60 °C; 20 to 85% humidity, non-condensing
Options
CU600 cutter Cuts paper and self-adhesive labels, cardboard, textile and synthetic materials up to 180 mm wide and 0.05 to 0.5 mm thick, at up to 100 cuts a minute and from a cutting length of 5 mm.
Peel-off versions Peel-off versions (P) peel labels off the liner on a peel-off plate and wind the liner on an internal rewinder (up to 142 mm across, on a 40 mm core); labels can be taken by hand or by an applicator.
External rewinders ER2/210 and ER6/300 rewinders wind a web up to 180 mm wide, outside or inside, on rolls up to 205 or 300 mm across, on a 40 mm core or a 76 mm cardboard core with an adapter.
Linerless The SQUIX 6.3 L prints direct thermal on linerless material at 203 or 300 dpi and up to 250 mm/s and cuts each label after the final print line; a retrofit kit converts a standard SQUIX 6.3.
Applicators and demand modules SQ 1000 stroke applicators apply labels 25 to 176 mm wide and 25 to 200 mm high from peel-off versions, and the S5106 demand module labels 50 to 176 mm wide and 25 to 210 mm high; cab calculates about 25 and 60 labels a minute.
USB WLAN stick A USB WLAN stick for 2.4 GHz 802.11b/g/n, or one with a rod antenna for 2.4 GHz and 5 GHz 802.11a/n/ac, in hotspot or infrastructure mode.
Digital I/O interface Digital I/O interface with 8 inputs and 8 outputs, to IEC/EN 61131-2 types 1 and 3, so that a PLC, a sensor or a hand switch can trigger printing; status and errors are signalled.
External unwinder An EU6/300 unwinder takes rolls up to 300 mm across for webs up to 180 mm wide.
Drivers and documents
- From cab: the drivers, firmware and user guide are on cab's page for the SQUIX 6.3.
- Set up as a fleet: cablabel S3, cabFirmwareUpdater.
- From SAP: through TEKLYNX SENTINEL, see 3.1 SAP label printing.
- From label software: through cab's driver, see Software licences.
- Calibration: PrinterCal, our own software, sets media sensor, darkness and print position on cab printers.
Printheads and wear parts
Part-number search| Part | cab part number |
|---|---|
| Printhead 6.3/200 (203 dpi) | 5977386.001 |
| Printhead 6.3/300 (300 dpi) | 5977387.001 |
| Print roller DR6 (platen roller) | 5954245.001 |
| Deflection roller RR6, peel-off versions | 5954246.001 |
The numbers are from cab SQUIX 6.3 spare parts list of Edition 01/2024, part no. 9003077. We supply these parts, and compatible ones, under our own article numbers.
What wears, and what shortens its life: 5.5 Printheads and wear parts.
cab's terms of 19 November 2024 give 24 months on the printer and, on the printhead, 24 months or 50 km of printing in thermal transfer or 24 months or 25 km in direct thermal, whichever comes first, with label material approved by cab in advance; wear parts such as the drive roller are not covered for wear.
Successor
The SQUIX 6.3 is current: cab has announced no end of sale.
It replaced the A6+. Older models and their successors are on 5.6 Discontinued models.
Around the printer

Installation: installed and commissioned by us, see 8.3 Installation. Outside Switzerland, each visit is quoted.

Repair: in our workshop near Zurich, see 8.1 Repair and RMA.

In a GMP plant: IQ and OQ support for cab printers, see 1.4 IQ/OQ/PQ scope.
For the SQUIX 6.3 on its own or with its installation, labels and ribbons, request a quote.
Last checked: 5 November 2026.
Preparing a validation, an inspection or a change to your labels?
The first engagement is free: a half-day review of your current label print chain, ending in a written list of gaps.




