cab MACH 4S
A 4 inch industrial label printer for thermal transfer and direct thermal labels, at up to 300 mm per second and up to 600 dpi.

maximum print width, MACH 4.3S at 300 dpi
maximum print speed, at 203 and 300 dpi
highest resolution, MACH 4S
weight
What fits the MACH 4S
Drawn to one scale.
Labels: 5 to 116 mm wide; 0.03 to 0.6 mm thick; on rolls up to 205 mm across, on a 38.1 to 76 mm core.
Ribbons: 25 to 114 mm wide and up to 360 m long, on a 25.4 mm core, wound with the ink side outside or inside. cab says a ribbon should be at least as wide as the liner material.
See , , or start from what the label must survive in the .
Specification
The base model. Options change some of these figures.
Printing
- Methods
- Thermal transfer; direct thermal on the MACH 4.3S and, as a possible mode, on the MACH 4S at 300 dpi, not at 600 dpi
- Resolution
- MACH 4.3S: 203 or 300 dpi; MACH 4S: 300 or 600 dpi
- Print width
- 104 mm at 203 dpi; 108.4 mm at 300 dpi on the MACH 4.3S; 105.7 mm at 300 and 600 dpi on the MACH 4S
- Print speed
- Up to 300 mm/s at 203 and 300 dpi; up to 150 mm/s at 600 dpi
- Print length
- Up to 13,500 mm at 203 dpi; 6,000 mm at 300 dpi; 1,500 mm at 600 dpi
- Media sensors
- Gap sensor, centred or shifted 10 mm to the left; reflective sensor from below, adjustable from the centre 56 mm to the left or 10 mm to the right; material passage up to 2 mm
Labels
- Width
- 5 to 116 mm
- Height
- From 5 mm without backfeed; from 12 mm with backfeed; from 20 mm for single-cut peel-off
- Roll
- Up to 205 mm outside diameter, on a 38.1 to 76 mm core; wound outside or inside
- Thickness
- 0.03 to 0.6 mm
- Liner
- 9 to 120 mm wide on a 38 mm core, 25 to 120 mm on a 76 mm core; 0.03 to 0.16 mm thick
- Continuous
- 5 to 120 mm wide on a 38 mm core, 25 to 120 mm on a 76 mm core; 0.03 to 0.5 mm thick; cardboard up to 180 g/m2
- Materials
- Paper, cardboard and synthetics (PET, PE, PP, PI, PVC, PU, acrylate, Tyvek) on rolls, reels or fanfold; shrink tube up to 120 mm wide and 1.1 mm thick; textile tape
Ribbons
- Length
- Up to 360 m
- Width
- 25 to 114 mm
- Core
- 25.4 mm
- Roll
- Up to 72 mm outside diameter; ink side outside or inside
Connections
- Standard
- RS232C, USB 2.0 Hi-Speed for a PC, Ethernet 10/100 Mbit/s with IPv4 and IPv6, static IP or DHCP, IEEE 802.1X, two USB host ports on the back, SD card slot (SDHC and SDXC, up to 512 GB), connection for the cutter or peel-off unit
- Optional
- USB WLAN stick, 2.4 GHz 802.11b/g/n, or with a rod antenna 2.4 GHz and 5 GHz 802.11a/n/ac
- Network protocols
- RawIP (port 9100 by default), LPD/LPR, FTP/FTPS, HTTP/HTTPS, WebDAV, SOAP, SNMP v2, SMTP, PJL, OPC UA and OPC UA DI, VNC, mDNS
Printer languages
- cab JScript and abc Basic Compiler; ZPL II as an option, with the data stream to be tested in advance
Unit
- Display
- 4.3 inch colour touch display, 480 x 272 px
- Versions
- Type B with tear-off edge; type P with peel-off; type C with cutter
- Memory
- 256 MB RAM, 50 MB flash (IFFS); 800 MHz 32-bit processor
- Size
- 240 x 317 x 435 mm, width by height by depth
- Weight
- 6 kg
- Power
- 100 to 240 V AC, 50/60 Hz, PFC; standby under 10 W, typical operation 80 W, up to 200 W
Environment
- Operating
- 5 to 40 °C; 10 to 85% humidity, non-condensing
- Storage
- 0 to 60 °C; 20 to 85% humidity, non-condensing
- Transport
- −25 to 60 °C; 20 to 85% humidity, non-condensing
Options
Peel-off version (type P) Peels printed labels off the liner and presents them, for labels from 12 mm high; the liner leads down behind the operation panel, and cab says peel-off has to be tested.
Cutter version (type C) Cuts labels and continuous materials from a cutting length of 12 mm, with a gap height of up to 2.5 mm, at up to 100 cuts a minute without material; the print job stops if the cutter does not reach its final position.
External rewinder ER4/210 Winds label webs outside or inside, for material up to 120 mm wide and rolls up to 210 mm across, on a 40 mm core or on a 76 mm cardboard core with an adapter; the adapter kit is included.
USB WLAN stick A USB WLAN stick for 2.4 GHz 802.11b/g/n, or one with a rod antenna for 2.4 GHz and 5 GHz 802.11a/n/ac, in hotspot or infrastructure mode. In hotspot mode a mobile device can connect directly to the printer.
External operation panel A second operation panel with the same functions, in landscape or portrait, for printers whose own panel cannot be reached; it connects by USB, with cables of 1.8 to 16 m.
Slim print rollers DR4-M25, DR4-M50 and DR4-M80 print rollers for slim materials and ribbons, which prevent print roller wear, printhead contamination and feed errors.
Drivers and documents
- From cab: the drivers, firmware and user guide are on cab's page for the MACH 4S.
- Set up as a fleet: cablabel S3, cabFirmwareUpdater.
- From SAP: through TEKLYNX SENTINEL, see 3.1 SAP label printing.
- From label software: through cab's driver, see Software licences.
- Calibration: PrinterCal, our own software, sets media sensor, darkness and print position on cab printers.
Printheads and wear parts
Part-number search| Part | cab part number |
|---|---|
| Printhead 4.3/200 (MACH 4.3S, 203 dpi) | 5977382.001 |
| Printhead 4.3/300 (MACH 4.3S, 300 dpi) | 5977383.001 |
| Printhead 4/300 (MACH 4S, 300 dpi) | 5977444.001 |
| Printhead 4/600 (MACH 4S, 600 dpi; needs firmware 5.44 or later) | 5987070.001 |
| Printhead holder, 600 dpi version (to be fitted with the 600 dpi printhead on printers up to serial number 84021) | 5984604.002 |
| Print roller DR4 (platen roller) | 5984649.001 |
The numbers are from cab MACH 4S spare parts list of Edition 09/2025, part no. 9003100. We supply these parts, and compatible ones, under our own article numbers.
What wears, and what shortens its life: 5.5 Printheads and wear parts.
cab's terms of 19 November 2024 give 24 months on the printer and, on the printhead, 24 months or 50 km of printing in thermal transfer or 24 months or 25 km in direct thermal, whichever comes first, with label material approved by cab in advance; wear parts such as the drive roller are not covered for wear.
Successor
The MACH 4S is current: cab has announced no end of sale.
It replaced the MACH4. Older models and their successors are on 5.6 Discontinued models.
Around the printer

Installation: installed and commissioned by us, see 8.3 Installation. Outside Switzerland, each visit is quoted.

Repair: in our workshop near Zurich, see 8.1 Repair and RMA.

In a GMP plant: IQ and OQ support for cab printers, see 1.4 IQ/OQ/PQ scope.
For the MACH 4S on its own or with its installation, labels and ribbons, request a quote.
Last checked: 5 November 2026.
Preparing a validation, an inspection or a change to your labels?
The first engagement is free: a half-day review of your current label print chain, ending in a written list of gaps.




