
Print and apply
A print and apply system prints each label as the product arrives and puts it on, with nobody touching it.
It comes in two forms:
A complete system from one maker, printer and applicator together, such as cab's HERMES Q, with an applicator for each method below.
How the line tells the system to print, and where the data comes from, is on 3.4 Labeling industrial automation.
Four ways to put a label on
MethodHow the label goes onSuits
- 01TampA pad takes the label as it is printed, and a stroke cylinder presses it onto the productProducts standing still; flat or recessed surfaces; products of different heights
- 02BlowThe pad stops 5 to 10 mm short of the product and a blast of air puts the label onSensitive surfaces, and products moving past
- 03Wipe onThe label goes from the printer straight onto the passing product and is wiped or rolled downA steady stream of products moving at the speed the printer prints
- 04Corner wrapHalf the label goes on one side, and the other half is rolled round onto the side next to itOne label across two sides of a box
cab's HQ applicators cover all four: stroke and swing applicators with tamp or blow pads, demand modules and vacuum belts for wipe on, and corner-wrap pads.
What decides between them
Moving or standing still.
A tamp pad needs the product at rest at the moment it applies. Blow, wipe on and corner wrap work on moving products.
Heights.
Tamp pads cope with products of different heights. A blow pad needs them uniform, unless a sensor stops it about 10 mm above each product, as on cab's HQ 4614.
Surface.
Flat, recessed, curved or easily marked. cab's HQ 5414 vacuum belt applies to cylinders; a blow pad never touches the surface.
Side.
Top, side, bottom, front or back. cab's HQ 3014 labels the front or back of moving packages.
Rate.
cab calculates about 20 labels a minute for its HQ 3214 swing applicator, about 30 for the HQ 4114 stroke applicator and about 60 for a demand module, each for a stated label height and print speed.
Label size.
cab's HQ applicators take labels from 4 to 250 mm high and 4 to 174 mm wide.
The printer inside
In a cab HERMES Q the printer is part of the system: the Q2 for small labels at 300 or 600 dpi, the Q4.3 and Q4 for labels up to 114 mm wide, and the Q6.3 for labels up to 174 mm, which cab builds for Odette, UCC and GS1 logistic labels. For linerless labels cab makes the HERMES QL; for two-colour GHS labels, the Hermes C.
Zebra's ZE511 prints 104 mm wide at up to 600 dpi, the ZE521 168 mm wide at up to 300 dpi. Both come in a right-hand and a left-hand version, as does cab's PX Q. The other print engines are on 5.1 Printer classes.

Connecting it to the line
- cab HERMES Q:
- digital inputs and outputs on a 25-pin SUB-D socket to IEC/EN 61131-2, 10 inputs and 11 outputs, plus Ethernet, RS-232, USB and OPC UA.
- cab PX Q:
- inputs and outputs at 24 V on a 25-pin, or at 5 V on a 15-pin SUB-D connector, plus Ethernet, RS-232, USB and OPC UA.
- Zebra ZE511 and ZE521:
- an applicator interface as standard, plus Ethernet, USB and RS-232.
Which signals the line controller sends, and how they are tested, is part of the integration on 3.4.
What stays with you
The space and mounting on the line, compressed air for pneumatic applicators, and the guarding around them.
Last checked: 21 October 2026.
Preparing a validation, an inspection or a change to your labels?
The first engagement is free: a half-day review of your current label print chain, ending in a written list of gaps.
