cab HERMES Q
A print and apply system for production lines, in 2, 4 and 6 inch print widths, at up to 300 mm per second and up to 600 dpi.

maximum print width, HERMES Q6.3 at 200 dpi
maximum print speed
highest resolution, Q2 and Q4
maximum label roll diameter
What fits the HERMES Q
Drawn to one scale.
Labels: 4 to 58 mm wide on the Q2, 10 to 114 mm on the Q4.3 and Q4, 46 to 174 mm on the Q6.3; up to 0.6 mm thick; on rolls up to 205 or 305 mm across, on a 76 mm core.
Ribbons: 25 to 67 mm wide on the Q2, 25 to 114 mm on the Q4.3 and Q4, 50 to 170 mm on the Q6.3, up to 600 m long, on a 25.4 mm core, wound with the ink side outside or inside; cab says the ribbon must be at least as wide as the liner tape.
See , , or start from what the label must survive in the .
Specification
The base model. Options change some of these figures.
Printing
- Methods
- Thermal transfer; direct thermal on the Q4.3 and Q6.3, not on the Q2 and Q4
- Resolution
- Q2: 300 or 600 dpi; Q4.3: 200 or 300 dpi; Q4: 300 or 600 dpi; Q6.3: 200 or 300 dpi
- Print width
- Q2: 56.9 mm at 300 dpi, 54.1 mm at 600 dpi; Q4.3: 104 mm at 200 dpi, 108.4 mm at 300 dpi; Q4: 105.7 mm; Q6.3: 168 mm at 200 dpi, 162.6 mm at 300 dpi
- Print speed
- Q2: up to 300 mm/s at 300 dpi, 150 mm/s at 600 dpi; Q4.3: 300 mm/s; Q4: 300 mm/s at 300 dpi, 150 mm/s at 600 dpi; Q6.3: 250 mm/s
- Print length
- Q2: up to 12,000 mm at 300 dpi, 3,000 mm at 600 dpi; Q4.3: 13,500 mm at 200 dpi, 6,000 mm at 300 dpi; Q4: 6,000 mm at 300 dpi, 1,500 mm at 600 dpi; Q6.3: 9,000 mm at 200 dpi, 4,000 mm at 300 dpi
- Media sensors
- Transmissive sensor and reflective sensor from below; 2 to 12 mm from the locating edge on the Q2 (2 to 26 mm with the modified sensor), 2 to 60 mm on the Q4.3, Q4 and Q6.3; material passage up to 2 mm
Applying
- Dispense direction
- To the left or to the right
- Mounting
- Assembled at 0°, 90°, 180° or 270°, or horizontal
- Applicators
- HQ applicators apply labels 4 to 250 mm high and 4 to 174 mm wide; stroke cylinders 200, 300 and 400 mm as standard, other lengths on request
Labels
- Width
- Q2: 4 to 58 mm; Q4.3 and Q4: 10 to 114 mm; Q6.3: 46 to 174 mm
- Height
- From 3 mm on the Q2; from 4 mm on the Q4.3 and Q4; from 6 mm on the Q6.3
- Roll
- Unwinder for rolls up to 205 mm or up to 305 mm outside diameter, on a 76 mm core; wound outside or inside; the Q2 also takes reels up to 205 mm
- Thickness
- Up to 0.6 mm
- Liner
- Q2: 24 to 62 mm wide; Q4.3 and Q4: 24 to 118 mm; Q6.3: 50 to 178 mm; 0.03 to 0.08 mm thick
- Liner rewinder
- Up to 155 or 205 mm outside diameter, on a 76 mm core
- Materials
- Paper, PET, PE, PP, PI, PVC, PU, acrylate and Tyvek labels on a roll
Ribbons
- Length
- Up to 600 m
- Width
- Q2: 25 to 67 mm; Q4.3 and Q4: 25 to 114 mm; Q6.3: 50 to 170 mm
- Core
- 25.4 mm
- Roll
- Up to 90 mm outside diameter; ink side outside or inside
Connections
- Standard
- RS232C, USB 2.0 Hi-Speed for a PC, Ethernet 10/100 Mbit/s with IPv4 and IPv6, static IP or DHCP, IEEE 802.1X, two USB host ports on the control panel and two on the back, SD card slot (SDHC and SDXC), USB host 24 V DC, digital I/O interface with 10 inputs and 11 outputs on a 25 pin SUB-D socket, to IEC/EN 61131-2 types 1 and 3
- Optional
- Interface for an external label sensor; 2-port Ethernet switch 10/100 Mbit/s; USB WLAN stick, 2.4 GHz 802.11b/g/n, or with a rod antenna 2.4 GHz and 5 GHz 802.11a/n/ac
- Network protocols
- RawIP (port 9100 by default), LPD/LPR, FTP/FTPS, HTTP/HTTPS, WebDAV, SOAP, SNMP v2, SMTP, PJL, OPC UA and OPC UA DI, VNC, mDNS
Printer languages
- cab JScript and abc Basic Compiler; ZPL II as an option, with the data stream to be tested in advance
Unit
- Display
- 4.3 inch colour touch display, 480 x 272 px; landscape or portrait, depending on how the unit is mounted
- Memory
- 256 MB RAM, 50 MB flash (IFFS); 800 MHz 32-bit processor
- Size
- Width 207 mm (Q2), 260 mm (Q4.3 and Q4), 320 mm (Q6.3); height 400 mm and depth 400 mm with a 205 mm roll, 430 mm and 500 mm with a 305 mm roll
- Weight
- Approx. 15 kg (205 mm roll) or 16 kg (305 mm roll) for the Q2; 16 or 17 kg for the Q4.3 and Q4; 20 kg for the Q6.3
- Power
- 100 to 240 V AC, 50/60 Hz, PFC; standby under 10 W, typical operation 100 W, up to 200 W
Environment
- Operating
- 5 to 40 °C; 10 to 85% humidity, non-condensing
- Storage
- 0 to 60 °C; 20 to 85% humidity, non-condensing
- Transport
- −25 to 60 °C; 20 to 85% humidity, non-condensing
Options
HQ applicators Front side, stroke, swing, stroke turn, flag and stroke blow applicators, demand modules, vacuum belt applicators and an air jet box take the printed label and apply it in real time to products at rest or in motion; cab calculates about 30 labels a minute for the HQ 4114 stroke applicator and about 60 for the HQ 5112 to 5116 demand modules.
UHF RFID module RS or HS read/write antennas on the printhead or the feeding unit, not on the Q2, fitted at the factory; with a 4214 applicator, defective labels can be ejected.
Automatic ribbon saving Lifts the printhead and stops the ribbon while labels feed, recommended where a label has at least 60 mm unprinted; fitted at the factory, not on the Q2 and not together with a UHF RFID module.
Label unwinder K40 and core adapters The K40 unwinder takes rolls on a 40 mm core, and adapters 40/50 and 76/100 take rolls on 50 mm and 100 mm cores from 20 mm wide.
Extended peel-off plate Adds 14 mm, recommended when a robotic arm picks up the label, when a readable area is needed for scanning, or when an antistatic brush is fitted.
USB WLAN stick and Ethernet switch A USB WLAN stick for 2.4 GHz, or with a rod antenna for 2.4 GHz and 5 GHz, and a 2-port Ethernet switch that connects another device to the same network.
External operation panel A second operation panel with the same functions, in landscape or portrait, for printers whose own panel cannot be reached; it connects by USB, with cables of 1.8 to 16 m.
CC200 scanner A CC200 scanner can be supplied on request.
Drivers and documents
- From cab: the drivers, firmware and user guide are on cab's page for the HERMES Q.
- Set up as a fleet: cablabel S3, cabFirmwareUpdater.
- From label software: through cab's driver, see Software licences.
- Calibration: PrinterCal, our own software, sets media sensor, darkness and print position on cab printers.
Printheads and wear parts
Part-number search| Part | cab part number |
|---|---|
| Printhead 2/300 (HERMES Q2, 300 dpi) | 5977384.001 |
| Printhead 2/600 (HERMES Q2, 600 dpi) | 5977385.001 |
| Printhead 4.3/200 (HERMES Q4.3, 200 dpi) | 5977382.001 |
| Printhead 4.3/300 (HERMES Q4.3, 300 dpi) | 5977383.001 |
| Printhead 4/300 (HERMES Q4, 300 dpi) | 5977444.001 |
| Printhead 4/600 (HERMES Q4, 600 dpi) | 5987070.001 |
| Printhead 6.3/200 (HERMES Q6.3, 200 dpi) | 5977386.001 |
| Printhead 6.3/300 (HERMES Q6.3, 300 dpi) | 5977387.001 |
| Print roller DR2 (HERMES Q2, platen roller) | 5954102.001 |
| Print roller DR4 (HERMES Q4.3 and Q4, platen roller) | 5954180.001 |
| Print roller DR6 (HERMES Q6.3, platen roller) | 5954245.001 |
| Print roller DRS2, silicone (HERMES Q2, option) | 5954978.001 |
| Print roller DRS4, silicone (HERMES Q4.3 and Q4, option) | 5954985.001 |
| Print roller DRS6, silicone (HERMES Q6.3, option) | 5954979.001 |
| Draw roller ZR2 (HERMES Q2) | 5961015.001 |
| Draw roller ZR4 (HERMES Q4.3 and Q4) | 5961298.001 |
| Draw roller ZR6 (HERMES Q6.3) | 5961220.001 |
The numbers are from cab HERMES Q left-hand spare parts list of Edition 07/2025, part no. 9003486. We supply these parts, and compatible ones, under our own article numbers.
What wears, and what shortens its life: 5.5 Printheads and wear parts.
cab's terms of 19 November 2024 give 24 months on print and apply systems and, on the printhead, 24 months or 50 km of printing in thermal transfer or 24 months or 25 km in direct thermal, whichever comes first, with label material approved by cab in advance; wear parts such as the drive roller are not covered for wear.
Successor
The HERMES Q is current: cab has announced no end of sale.
It replaced the Hermes+. Older models and their successors are on 5.6 Discontinued models.
Around the printer

Installation: installed and commissioned by us, see 8.3 Installation. Outside Switzerland, each visit is quoted.

Repair: in our workshop near Zurich, see 8.1 Repair and RMA.

In a GMP plant: IQ and OQ support for cab printers, see 1.4 IQ/OQ/PQ scope.
For the HERMES Q on its own or with its installation, labels and ribbons, request a quote.
Last checked: 5 November 2026.
Preparing a validation, an inspection or a change to your labels?
The first engagement is free: a half-day review of your current label print chain, ending in a written list of gaps.




