cab MACH1 and MACH2
4 inch desktop label printers for thermal transfer and direct thermal labels, at up to 177 mm per second and up to 300 dpi.

maximum print width, at 203 dpi
maximum print speed, MACH2 at 203 dpi
highest resolution
maximum label roll diameter
What fits the MACH1 and MACH2
Drawn to one scale.
Labels: 25 to 112 mm wide, up to 118 mm for continuous material; 0.06 to 0.2 mm thick; on rolls up to 127 mm across, on a 25.4 to 38.1 mm core.
Ribbons: 25 to 114 mm wide and up to 300 m long, on a 25.4 mm core, wound with the ink side outside or inside.
See , , or start from what the label must survive in the .
Specification
The base model. Options change some of these figures.
Printing
- Methods
- Thermal transfer and direct thermal
- Resolution
- 203 dpi and 300 dpi
- Print width
- Up to 108 mm at 203 dpi; up to 105.7 mm at 300 dpi
- Print speed
- MACH1: up to 127 mm/s at 203 dpi, 102 mm/s at 300 dpi; MACH2: up to 177 mm/s at 203 dpi, 127 mm/s at 300 dpi
- Print length
- Up to 1,727 mm at 203 dpi; up to 762 mm at 300 dpi
- Media sensors
- Gap sensor fixed at the centre; reflective sensor from below, adjustable
Labels
- Width
- 25 to 112 mm; liner or continuous material 25 to 118 mm
- Height
- From 4 mm
- Roll
- Up to 127 mm outside diameter, on a 25.4 to 38.1 mm core; wound outside or inside
- Thickness
- 0.06 to 0.2 mm; 60 to 160 g/m2
- Materials
- Paper, cardboard and plastics; continuous material on a roll or fanfold
Ribbons
- Length
- Up to 300 m
- Width
- 25 to 114 mm
- Core
- 25.4 mm
- Roll
- Up to 68 mm outside diameter; ink side outside or inside
Connections
- Standard
- RS232C, USB for a PC, Ethernet; USB host on the MACH2 only
Printer languages
- EZPL
Unit
- Display
- MACH1: Ready and Status LEDs, with Feed, On/off and sensor calibration buttons; MACH2: colour TFT display with navigator pad
- Memory
- 16 MB flash; 8 MB SDRAM, 4 MB of it for the application
- Size
- 210 x 186 x 280 mm, width by height by depth
- Weight
- MACH1 2.7 kg; MACH2 3 kg
- Power
- 100 to 240 V AC, 50/60 Hz, PFC; up to 60 W
Environment
- Operating
- 5 to 40 °C; 30 to 85% humidity, non-condensing
- Storage
- −20 to 50 °C; 10 to 90% humidity, non-condensing
- Transport
- −25 to 60 °C; 20 to 80% humidity, non-condensing
Options
Cutter A cutter with a cutting height between labels of at least 30 mm.
Present sensor A present sensor for labels at least 25 mm high.
External unwinder An external unwinder for label rolls up to 250 mm across.
Drivers and documents
- From cab: the drivers, firmware and user guide are on cab's page for the MACH1 and MACH2.
- Set up as a fleet: cablabel S3, NetworkSettingSetup.
- From SAP: through TEKLYNX SENTINEL, see 3.1 SAP label printing.
- From label software: through cab's driver, see Software licences.
- Calibration: PrinterCal, our own software, sets media sensor, darkness and print position on cab printers.
Printheads and wear parts
We supply printheads and wear parts for the printers we sell, the printer maker's own and compatible ones. Send us the model and, if you have it, the serial number at [email protected], and we name the part.
What wears, and what shortens its life: 5.5 Printheads and wear parts.
cab's terms of 19 November 2024 give 24 months on the printer and, on the printhead, 24 months or 50 km of printing in thermal transfer or 24 months or 25 km in direct thermal, whichever comes first, with label material approved by cab in advance; wear parts such as the drive roller are not covered for wear.
Status
The MACH1 and MACH2 are current: cab has announced no end of sale.
Older models and their successors are on 5.6 Discontinued models.
Around the printer

Installation: installed and commissioned by us, see 8.3 Installation. Outside Switzerland, each visit is quoted.

Repair: in our workshop near Zurich, see 8.1 Repair and RMA.

In a GMP plant: IQ and OQ support for cab printers, see 1.4 IQ/OQ/PQ scope.
For the MACH1 and MACH2 on its own or with its installation, labels and ribbons, request a quote.
Last checked: 5 November 2026.
Preparing a validation, an inspection or a change to your labels?
The first engagement is free: a half-day review of your current label print chain, ending in a written list of gaps.




