cab PX Q
A 4 or 6 inch print module for print and apply lines, at up to 300 mm per second and up to 600 dpi, in left-hand and right-hand versions.

maximum print width, PX Q6.3 at 203 dpi
maximum print speed
highest resolution, PX Q4
weight of the 4 inch modules
What fits the PX Q
Drawn to one scale.
Labels: 10 to 116 mm wide on the PX Q4.3 and PX Q4 and 50 to 174 mm on the PX Q6.3; up to 0.6 mm thick; cab gives no roll size for the module.
Ribbons: 25 to 114 mm wide on the PX Q4.3 and PX Q4 and 50 to 170 mm on the PX Q6.3, up to 600 m long, on a 25.4 mm core, wound with the ink side outside or inside; cab says a ribbon should be at least as wide as the liner material.
See , , or start from what the label must survive in the .
Specification
The base model. Options change some of these figures.
Printing
- Methods
- Thermal transfer; direct thermal on the PX Q4.3 and PX Q6.3, not on the PX Q4
- Resolution
- PX Q4.3: 203 or 300 dpi; PX Q4: 300 or 600 dpi; PX Q6.3: 203 or 300 dpi
- Print width
- PX Q4.3: 104 mm at 203 dpi, 108.4 mm at 300 dpi; PX Q4: 105.7 mm; PX Q6.3: 168 mm at 203 dpi, 162.6 mm at 300 dpi
- Print speed
- PX Q4.3: up to 300 mm/s; PX Q4: 300 mm/s at 300 dpi, 150 mm/s at 600 dpi; PX Q6.3: 250 mm/s
- Print length
- PX Q4.3: up to 13,500 mm at 203 dpi, 6,000 mm at 300 dpi; PX Q4: 6,000 mm at 300 dpi, 1,500 mm at 600 dpi; PX Q6.3: 9,000 mm at 203 dpi, 4,000 mm at 300 dpi
- Label transfer
- To the left (L) or to the right (R), as two versions
- Media sensors
- Gap sensor and reflective sensor from below, 4 to 60 mm from the locating edge; material passage up to 2 mm
Labels
- Width
- PX Q4.3 and PX Q4: 10 to 116 mm; PX Q6.3: 50 to 174 mm
- Height
- PX Q4.3 and PX Q4: from 6 mm without backfeed, 12 mm with backfeed; PX Q6.3: from 12 mm and 25 mm
- Thickness
- Up to 0.6 mm
- Liner
- PX Q4.3 and PX Q4: 16 to 120 mm wide; PX Q6.3: 50 to 178 mm; 0.03 to 0.16 mm thick
- Materials
- Paper and plastics such as PET, PE, PP, PI, PVC, PU, acrylate and Tyvek
Ribbons
- Length
- Up to 600 m
- Width
- PX Q4.3 and PX Q4: 25 to 114 mm; PX Q6.3: 50 to 170 mm
- Core
- 25.4 mm
- Roll
- Up to 90 mm outside diameter; ink side outside or inside
Connections
- Standard
- RS232C, USB 2.0 Hi-Speed for a PC, Ethernet 10/100 Mbit/s with IPv4 and IPv6, static IP or DHCP, IEEE 802.1X, two USB host ports on the control panel and two on the back, SD card slot (SDHC and SDXC)
- Optional
- Digital I/O interface 24 V DC with 8 inputs and 9 outputs (25 pin SUB-D) or 5 V DC with 5 inputs and 6 outputs (15 pin SUB-D), to IEC/EN 61131-2 types 1 and 3; 2-port Ethernet switch 10/100 Mbit/s; interface for an external label sensor (M12, 5 pins); USB WLAN stick
- Network protocols
- RawIP (port 9100 by default), LPD/LPR, FTP/FTPS, HTTP/HTTPS, WebDAV, SOAP, SNMP v2, SMTP, PJL, OPC UA and OPC UA DI, VNC, mDNS
Printer languages
- cab JScript and abc Basic Compiler; ZPL II as an option, with the data stream to be tested in advance
Unit
- Display
- 4.3 inch colour touch display, 480 x 272 px; landscape or portrait, depending on how the module is mounted
- Mounting
- Any orientation of assembly; cast aluminium chassis
- Memory
- 256 MB RAM, 50 MB flash (IFFS); 800 MHz 32-bit processor
- Size
- PX Q4.3 and PX Q4: 245 x 300 x 333 mm; PX Q6.3: 245 x 300 x 393 mm, width by height by depth
- Weight
- PX Q4.3 and PX Q4: 11.5 kg; PX Q6.3: 12 kg
- Power
- 100 to 240 V AC, 50/60 Hz, PFC; standby under 10 W, typical operation 100 W, up to 200 W
Environment
- Operating
- 5 to 40 °C; 10 to 85% humidity, non-condensing
- Storage
- 0 to 60 °C; 20 to 85% humidity, non-condensing
- Transport
- −25 to 60 °C; 20 to 85% humidity, non-condensing
Options
Automatic ribbon saving Lifts the printhead and stops the ribbon while labels feed, recommended where a label has at least 60 mm unprinted; fitted at the factory.
Print roller DRS A silicone-coated print roller with an extra long life, which takes a higher print offset on a label into account.
Digital I/O interface 24 V DC A 25 pin SUB-D socket with 8 inputs and 9 outputs, to IEC/EN 61131-2 types 1 and 3, galvanically isolated, with short-circuit protected outputs.
Digital I/O interface 5 V DC A 15 pin SUB-D socket with 5 inputs and 6 outputs, to IEC/EN 61131-2 types 1 and 3.
2-port Ethernet switch Connects another device to the same network, with the signals looped through.
External label sensor interface An M12 plug, 5 pins, a-coded, compatible with sensors based on PNP and 24 V.
External operation panel A second operation panel with the same functions, in landscape or portrait, for printers whose own panel cannot be reached; it connects by USB, with cables of 1.8 to 16 m.
Interface cover unit Protects the interfaces from humidity and contamination.
Drivers and documents
- From cab: the drivers, firmware and user guide are on cab's page for the PX Q.
- Set up as a fleet: cablabel S3, cabFirmwareUpdater.
- From SAP: through TEKLYNX SENTINEL, see 3.1 SAP label printing.
- From label software: through cab's driver, see Software licences.
- Calibration: PrinterCal, our own software, sets media sensor, darkness and print position on cab printers.
Printheads and wear parts
Part-number search| Part | cab part number |
|---|---|
| Printhead 4.3/200 (PX Q4.3, 203 dpi) | 5977382.001 |
| Printhead 4.3/300 (PX Q4.3, 300 dpi) | 5977383.001 |
| Printhead 4/300 (PX Q4, 300 dpi) | 5977444.001 |
| Printhead 4/600 (PX Q4, 600 dpi) | 5987070.001 |
| Printhead 6.3/200 (PX Q6.3, 203 dpi) | 5977386.001 |
| Printhead 6.3/300 (PX Q6.3, 300 dpi) | 5977387.001 |
| Print roller DR4 (4 inch modules, platen roller) | 5954180.001 |
| Print roller DR6 (PX Q6.3, platen roller) | 5954245.001 |
| Backfeed roller, 4 inch | 5965010.001 |
| Backfeed roller, 6 inch | 5965020.001 |
| Deflection roller, 4 inch | 5956117.001 |
| Deflection roller, 6 inch | 5956275.001 |
| Pressure roller, 4 inch | 5965016.001 |
| Pressure roller, 6 inch | 5965019.001 |
The numbers are from cab PX Q spare parts list of Edition 10/2025, part no. 9003526. We supply these parts, and compatible ones, under our own article numbers.
What wears, and what shortens its life: 5.5 Printheads and wear parts.
cab's terms of 19 November 2024 give 24 months on print and apply systems and, on the printhead, 24 months or 50 km of printing in thermal transfer or 24 months or 25 km in direct thermal, whichever comes first, with label material approved by cab in advance; wear parts such as the drive roller are not covered for wear.
Successor
The PX Q is current: cab has announced no end of sale.
It replaced the PX. Older models and their successors are on 5.6 Discontinued models.
Around the printer

Installation: installed and commissioned by us, see 8.3 Installation. Outside Switzerland, each visit is quoted.

Repair: in our workshop near Zurich, see 8.1 Repair and RMA.

In a GMP plant: IQ and OQ support for cab printers, see 1.4 IQ/OQ/PQ scope.
For the PX Q on its own or with its installation, labels and ribbons, request a quote.
Last checked: 5 November 2026.
Preparing a validation, an inspection or a change to your labels?
The first engagement is free: a half-day review of your current label print chain, ending in a written list of gaps.




