cab XD Q
A 4 inch printer that prints both sides of a material with two printheads, at 300 dpi and 150 mm per second, or 600 dpi up to 54.1 mm wide.

maximum print width, at 300 dpi
maximum print speed, at 300 dpi
highest resolution, up to 54.1 mm wide
printed with two printheads
What fits the XD Q
Drawn to one scale.
Labels: 10 to 110 mm wide; up to 0.1 mm thick; on rolls up to 300 mm across, on a 38.1 to 76 mm core; continuous material 4 to 114 mm wide.
Ribbons: Up to 114 mm wide and up to 450 m long, on a 25.4 mm core, wound with the colour side outside or inside; one ribbon runs through each printhead, and cab says ribbons should be at least as wide as the liner material.
See , , or start from what the label must survive in the .
Specification
The base model. Options change some of these figures.
Printing
- Methods
- Thermal transfer on both sides of the material, with two printheads
- Resolution
- XD Q4/300: 300 dpi; XD Q4.2/600: 600 dpi
- Print width
- Up to 105.7 mm at 300 dpi; up to 54.1 mm at 600 dpi, with a DR4-M60 print roller
- Print speed
- Up to 150 mm/s at 300 dpi; up to 100 mm/s at 600 dpi
- Print length
- Up to 3,000 mm at 300 dpi; up to 1,500 mm at 600 dpi
- Printheads
- 300 dpi and 600 dpi printheads not interchangeable; separate heating setting for each printhead; printhead 1 lifted when only printhead 2 prints the top; automated ribbon saving on printhead 1
- Media sensors
- Transmissive sensor and reflective sensor from below or above, 0 to 55 mm from the centre; material passage up to 2 mm
Labels
- Width
- 10 to 110 mm
- Height
- From 20 mm
- Roll
- Up to 300 mm outside diameter, on a 38.1 to 76 mm core; wound outside or inside
- Thickness
- Up to 0.1 mm
- Liner
- 14 to 114 mm wide; 0.03 to 0.16 mm thick
- Continuous
- 4 to 114 mm wide; 0.03 to 0.5 mm thick; cardboard up to 300 g/m2
- Materials
- Paper, cardboard and synthetics (PET, PE, PP, PI, PVC, PU, acrylate, Tyvek) on rolls or fanfold, guided in centred position; shrink tube ready for use up to 114 mm wide or continuous pressed 4 to 85 mm wide, up to 1.1 mm thick; textile tape
Ribbons
- Length
- Up to 450 m
- Width
- Up to 114 mm
- Core
- 25.4 mm
- Roll
- Up to 80 mm outside diameter; colour side outside or inside
Connections
- Standard
- RS232-C, USB 2.0 Hi-Speed for a PC, Ethernet 10/100 Mbit/s with IPv4 and IPv6, static IP or DHCP, IEEE 802.1X, two USB host ports on the control panel and two on the back, SD card slot (SDHC and SDXC, up to 512 GB), USB host 24 V DC for peripherals
- Optional
- Digital I/O interface with 8 inputs and 8 outputs; USB WLAN stick, 2.4 GHz 802.11b/g/n, or with a rod antenna 2.4 GHz and 5 GHz 802.11a/n/ac
- Network protocols
- RawIP (port 9100 by default), LPD/LPR, FTP/FTPS, HTTP/HTTPS, WebDAV, SOAP, SNMP v2, SMTP, PJL, OPC UA and OPC UA DI, VNC, mDNS
Printer languages
- cab JScript and abc Basic Compiler; ZPL II as an option, with the data stream to be tested in advance
Unit
- Display
- 4.3 inch colour touch display, 272 x 480 px
- Memory
- 256 MB RAM, 50 MB flash (IFFS); 800 MHz 32-bit processor
- Size
- 248 x 395 x 594 mm, width by height by depth
- Weight
- 21 kg
- Power
- 100 to 240 V AC, 50/60 Hz, PFC; typical operation 100 W, up to 200 W
Environment
- Operating
- 5 to 40 °C; 10 to 85% humidity, non-condensing
- Storage
- 0 to 60 °C; 20 to 85% humidity, non-condensing
- Transport
- −25 to 60 °C; 20 to 85% humidity, non-condensing
Options
Cutters and perforation cutters A CSQ 402 cutter and PSQ 403 perforation cutter, or CU400 and PCU400, handle paper, cardboard, textile and synthetic materials and shrink tubes; the CSQ and PSQ pivot away to change material and cut at up to 200 cuts a minute, against 100 for the CU and PCU.
External rewinders ER4/210 and ER4/300 rewinders wind a web up to 120 mm wide, outside or inside, on rolls up to 205 or 300 mm across, on a 76 mm tightening axle.
UHF RFID OM module On request for the XD Q4/300: the module sits in the chassis with its antenna on the printhead, tags are read and written just before the label is printed, and a label is marked invalid after errors.
Adapter 40/100 Holds label rolls on a 100 mm core; one adapter is enough for material no more than 50 mm wide.
ST400 M stacker with cutter Cuts printed material 20 to 100 mm wide and 20 to 150 mm long and collects up to 100 mm of it; printing stops when the limit is reached.
Slim print rollers DR4-M30, DR4-M60 and DR4-M80 rubber rollers and DRS4-M35 and DRS4-M50 silicone rollers for narrow materials and ribbons; cab prefers silicone for textile work and for very long life.
Transport rollers for the separator A TR4 rubber roller, 120 mm wide, preferred for shrink tube work, and a TR4-M60, 60 mm wide, preferred for textile work; steel is standard for textile.
USB WLAN stick A USB WLAN stick for 2.4 GHz 802.11b/g/n, or one with a rod antenna for 2.4 GHz and 5 GHz 802.11a/n/ac, in hotspot or infrastructure mode.
Drivers and documents
- From cab: the drivers, firmware and user guide are on cab's page for the XD Q.
- Set up as a fleet: cablabel S3, cabFirmwareUpdater.
- From SAP: through TEKLYNX SENTINEL, see 3.1 SAP label printing.
- From label software: through cab's driver, see Software licences.
- Calibration: PrinterCal, our own software, sets media sensor, darkness and print position on cab printers.
Printheads and wear parts
Part-number search| Part | cab part number |
|---|---|
| Printhead 4/300 X (XD Q4/300, 300 dpi; two per printer) | 5987089.001 |
| Printhead 2/600 (XD Q4.2/600, 600 dpi; two per printer) | 5987330.001 |
| Printhead 4/300 RFID (lower printhead of the XD Q4/300 with UHF RFID module) | 6011937.001 |
| Print roller DR4 (XD Q4/300, platen roller; two per printer) | 5954180.001 |
| Print roller DR4-M60 (XD Q4.2/600; an option on the XD Q4/300) | 5953701.001 |
| Print roller DR4-M80 (option on the XD Q4/300) | 5953702.001 |
| Print roller DR4-M30 (option) | 5953700.001 |
The numbers are from cab XD Q spare parts list of Edition 07/2026, part no. 9003848. We supply these parts, and compatible ones, under our own article numbers.
What wears, and what shortens its life: 5.5 Printheads and wear parts.
cab's terms of 19 November 2024 give 24 months on the printer and, on the printhead, 24 months or 50 km of printing in thermal transfer or 24 months or 25 km in direct thermal, whichever comes first, with label material approved by cab in advance; wear parts such as the drive roller are not covered for wear.
Status
The XD Q is current: cab has announced no end of sale.
Older models and their successors are on 5.6 Discontinued models.
Around the printer

Installation: installed and commissioned by us, see 8.3 Installation. Outside Switzerland, each visit is quoted.

Repair: in our workshop near Zurich, see 8.1 Repair and RMA.

In a GMP plant: IQ and OQ support for cab printers, see 1.4 IQ/OQ/PQ scope.
For the XD Q on its own or with its installation, labels and ribbons, request a quote.
Last checked: 5 November 2026.
Preparing a validation, an inspection or a change to your labels?
The first engagement is free: a half-day review of your current label print chain, ending in a written list of gaps.




